Search

Skip To Content

PAY YOUR INVOICE

855 GEN ESSE (855 436 3773)

Overlay

PAY YOUR INVOICE

Products
Service
Resources
About Us
Contact Us

call 855 GEN ESSE (855 436 3773) mail_outline info@essellc.com search Request A Quote Request A Quote

Startup Request

Home > Startup Request

Step 1 of 10

10%

Project Name*
Project Site Contact*
Project Contact Phone*
Project Contact Email*
Project Address*
Project City*
Project County*
Project State*
Project Zip*

Owner Company Name*
Owner Contact Name*
Owner Phone*
Owner Email*
Owner Address*
Owner City*
Owner County*
Owner State*
Owner Zip*

*Required
Electrical Contractor
Electrical Contractor Company Name*
Electrical Contractor Contact Name*
Electrical Contractor Email*
Electrical Contractor Phone*

*Required
Generator System Information
Model Number 1*
Serial Number 1*
Model Number 2
Serial Number 2
Model Number 3
Serial Number 3

*Required
Transfer Switch Information
Model Number 1*
Serial Number 1*
Model Number 2
Serial Number 2
Model Number 3
Serial Number 3
Model Number 4
Serial Number 4

*Required
Scheduling Information
Please note we do request a minimum two (2) weeks' notice for scheduling. We will contact you to confirm availability and schedule. Please do not assume your date requested is scheduled until you have confirmation from the ESSE office.
Is there a specific date you would like to request a startup?
DD slash MM slash YYYY
Will we be allowed to perform a simulated power failure to complete the system test at startup? Additional charges may apply for return trips.*
- Yes
- No
Is there a specific time window we can complete a simulated power failure test? List below. Additional charges may apply for times outside M-F, 8am-5pm.*
Operational Training is usually conducted the same day as startup. Will the end-user or representative be available the day of startup for training?*
- Yes
- No
If NO, what Date and Time can training be scheduled for? Additional charges may apply.
How close can a tech park to the generator?*

Fuel System Information
Fuel System
- Gas
- Diesel

*Required
Gas Fuel System
If you have selected Gas as your fuel system. IT IS THE INSTALLER'S RESPONSIBILITY TO PROPERLY SIZE THE PIPING AND REGULATORS.
Select Gas type*
- Natural Gas
- LP Vapor
- LP Liquid
Is the gaseous fuel system hooked up using a proper Flex Fuel Line and Regulator?*
- Yes
- No
Correct NG or LP fuel pressure and volume? Refer to Generac Manual 10000046207 Fuel Supply piping for Industrial Generators.*
- Yes
- No
Inches of Water Column or Ounces of Pressure at Generator*
Pipe size*
BTU of Primary Regulator*
Length of pipe between Primary Regulator and Generator*
Manual shut-off valve and all applicable safety valves are installed per local codes and standards. A manual shut-off valve and pressure test port (tee) should be installed near the generator:*
- Yes
- No
Is this a dedicated fuel line for the generator(s)?*
- Yes
- No
Number of 90 degree elbows installed:*
Number of 45 degree elbows installed:*
Number of Tees installed:*
Make of Regulator:*
Model Number of Regulator:*
*Required
Diesel Fuel System
If you have selected Diesel for your fuel system.
Is a Fuel Tank Pressure Test required? If yes, DO NOT fuel unit.*
- Yes
- No
How many gallons of fuel in unit?*

*Required
Electrical System
Utility power is available with nominal voltage:*
- 240V 1-Phase
- 208V 3-Phase
- 240V 3-Phase
- 480V 3-Phase
Generator set is grounded in compliance with local codes.*
- Yes
- No
Generator and ATS data plate voltages match utility voltage.*
- Yes
- No
Control wires are run in separate wiring away from AC wiring.*
- Yes
- No
AC wiring is properly sized, installed, and terminated. Note: ESSE will NOT terminate AC wiring.*
- Yes
- No
Building loads are properly connected in ATS.*
- Yes
- No
Remote Emergency Stop Switch is installed.*
- Yes
- No
- N/A
Remote Annunciator Panel (RAP) installed.*
- Yes
- No
- N/A
Wires run and labeled from generator to annunciator panel.*
- Yes
- No
- N/A
Generator is securely mounted and anchored to the concrete pad.*
- Yes
- No
Exhaust System is installed if it shipped loose.*
- Yes
- No
- N/A
Battery Charger Circuit run from the emergency distribution panel.*
- Yes
- No
- N/A
Engine Block Heater Circuit run and terminated at the generator.*
- Yes
- No
- N/A
GFCI Receptacle and/or Load Center, if used, is installed and connected.*
- Yes
- No
- N/A
Starting Battery has been set in the unit. *Do Not Connect Batteries, Technician will connect at startup. All circuits must be run and terminated. No Power is to be supplied to the circuits at the generator until startup. Powering these circuits can cause damage to the unit not covered under warranty.*
- Yes
- No

*Required
Signature

Please Note: If the ESSE technician arrives on site for startup and determines that this checklist was not followed and the start-up cannot be performed, Additional Charges will apply for all necessary return trips or the time it takes to perform the corrections while the technician is on site. Additional charges will be at our normal rates.

Overtime rates (1.5X normal rates) apply to hours beyond the standard workday M-F, 8am-5pm.

Normal Rates $168 Hr-Labor, $168 Hr-Travel, and $3.25 per mile.

Form completely by:
Company*
Email*
Phone*
Printed Name as Signature*
Date Signed
DD slash MM slash YYYY
Captcha
Name
This field is for validation purposes and should be left unchanged.

Δ

Request A Generator Quote

Get in touch with our sales team to receive a quote »

Interactive Sales Map

Find and contact your sales representative

Newsletter Sign Up

Support
Employment
Products
Service
Contact

HEADQUARTERS: 3235 Veterans Circle, Birmingham, Alabama 35235 EMERGENCY CONTACT: 855 GEN ESSE (855 436 3773)

© 2024 Energy Systems Southeast, LLC | Site created by Thomas Marketing Services

Privacy Policy
Sitemap
Terms of Service